AV-3030RDX

Transcript

AV-3030RDX
2,4-GHz-FUNKSYSTEM
EMPFÄNGER FÜR DEN AUSSENBEREICH
2.4 GHz WIRELESS TRANSMISSION SYSTEM
RECEIVER FOR OUTDOOR APPLICATIONS
AV-3030RDX
Best.-Nr. 18.8080
MONTAGEANLEITUNG
MOUNTING INSTRUCTIONS
NOTICE D’UTILISATION
ISTRUZIONI PER IL MONTAGGIO
®
DEUTSCH
Bevor Sie einschalten …
ENGLISH
Before switching on …
Wir wünschen Ihnen viel Spaß mit Ihrem neuen
Gerät von MONACOR. Bitte lesen Sie diese
Bedienungsanleitung vor dem Betrieb gründlich
durch. Nur so lernen Sie alle Funktionsmöglichkeiten kennen, vermeiden Fehlbedienungen
und schützen sich und Ihr Gerät vor eventuellen
Schäden durch unsachgemäßen Gebrauch.
Heben Sie die Anleitung für ein späteres Nachlesen auf.
Der deutsche Text beginnt auf der Seite 6.
FRANÇAIS
Avant toute installation …
ITALIANO
We wish you much pleasure with your new
MONACOR unit. Please read these operating
instructions carefully prior to operating the unit.
Thus, you will get to know all functions of the
unit, operating errors will be prevented, and
yourself and the unit will be protected against
any damage caused by improper use. Please
keep the operating instructions for later use.
The English text starts on page 8.
Prima di accendere …
Nous vous souhaitons beaucoup de plaisir à utiliser cet appareil MONACOR. Lisez ce mode
d'emploi entièrement avant toute utilisation.
Uniquement ainsi, vous pourrez apprendre l’ensemble des possibilités de fonctionnement de
l’appareil, éviter toute manipulation erronée et
vous protéger, ainsi que l’appareil, de dommages éventuels engendrés par une utilisation
inadaptée. Conservez la notice pour pouvoir
vous y reporter ultérieurement.
La version française se trouve page 10.
Vi auguriamo buon divertimento con il vostro
nuovo apparecchio di MONACOR. Leggete
attentamente le istruzioni prima di mettere in
funzione l'apparecchio. Solo così potete conoscere tutte le funzionalità, evitare comandi
sbagliati e proteggere voi stessi e l'apparecchio
da eventuali danni in seguito ad un uso improprio. Conservate le istruzioni per poterle consultare anche in futuro.
Il testo italiano inizia a pagina 12.
3
4
1
2
3
4
5
1
➀
6 7 8
Unterseite
Bottom side
Partie inférieure
Lato inferiore
9
BCD
2 3 45
01
EF
6789A
1
2
3
4
5
6
7
8
9
10
invers
Videopegel
10
3
4
normal
Auto - Time
5
➁
max. 80 mA
GND
DC +7.. 30 V
GND
Audio B
GND
Audio A
GND
Video
GND
Sw. Ch.
11
Innenteil
Inside part
Partie intérieure
Parte interna
+
AV-3030RDX
R1
D1
0–15V
10
Sw. Ch.
9
GND
➂
Anschluss des Schaltkanals
Connection of the control channel
Branchement du canal de commutation
Connessione del canale di commutazione
5
DEUTSCH
Bitte klappen Sie die Seite 5 heraus. Sie sehen
dann immer die beschriebenen Bedienelemente
und Anschlüsse.
1
1
2
3
4
5
6
7
8
9
10
11
2
Übersicht der Bedienelemente und
Anschlüsse
Rastnase zum Festhalten des Gehäuses
Innenteil (siehe auch Abb. 2)
Wand- und Masthalterung
SMA-Antennenbuchse
Kabeldurchführung
Regler für die Verweildauer (ca. 1 – 20 s) eines
Kamerabildes im Umschaltbetrieb
interne Betriebsanzeige
Drehschalter zum Einstellen des Empfangskanals
Pos.
Kanal
0, 1
1
2
2
3
3
4
4
5
5
6, 7, 8 1
9
autom. Umschalten zwischen 1 + 5
A
autom. Umschalten zwischen 1 + 3 + 5
B–F
1
10-polige Klemmleiste für sämtliche Anschlüsse,
für Drahtquerschnitte von 0,14 – 1 mm2
(Zum Hineinstecken oder Herausziehen eines
Drahtes die zugehörige orange Lasche drücken.)
Regler zum Korrigieren des Videopegels;
der Videopegel ist normgerecht eingestellt (1 Vss),
lässt sich jedoch auf 0,7 – 1,2 Vss ändern
Umschalter für die Videosignalpolarität
normal normgerechte Polarität
invers das Videosignal wird invertiert;
(zur verschlüsselten Übertragung, wenn
der Sender ebenfalls das Videosignal invertiert senden kann)
Wichtige Hinweise für den Gebrauch
Der Empfänger entspricht allen erforderlichen Richtlinien der EU und ist deshalb mit
gekennzeichnet.
● Betreiben Sie den Empfänger nicht in Bereichen
mit sehr hohen oder sehr niedrigen Temperaturen
(zulässiger Einsatztemperaturbereich -10 °C bis
+55 °C).
● Verwenden Sie für die Reinigung des Gehäuses
keine scharfen Reinigungsmittel oder Chemikalien.
● Wird der Empfänger zweckentfremdet, nicht richtig
installiert, falsch bedient oder nicht fachgerecht
repariert, kann keine Haftung für daraus resultierende Sach- oder Personenschäden und keine
Garantie für den Empfänger übernommen werden.
Soll der Empfänger endgültig aus dem
Betrieb genommen werden, übergeben Sie
ihn zur umweltgerechten Entsorgung einem
örtlichen Recyclingbetrieb.
6
3
Einsatzmöglichkeiten
Der Empfänger AV-3030RDX dient in Verbindung mit
einem 2,4-GHz-Sender oder einer 2,4-GHz-FunkÜberwachungskamera der Serie „AV-...“ von
MONACOR zur drahtlosen Übertragung von Ton und
Bild. Mit zusätzlichen Geräten aus dem Programm
von MONACOR lässt sich eine drahtlose Video-Überwachungsanlage aufbauen. Durch das wetterfeste
Gehäuse (IP 54) ist der AV-3030RDX speziell zur
Montage im Außenbereich geeignet.
Die Übertragungsreichweite hängt stark von den
örtlichen Gegebenheiten, dem verwendeten Sender
und der verwendeten Empfangsantenne ab. Bei
Sichtverbindung kann sie bis zu 500 m betragen, in
Gebäuden bis zu 50 m je nach Beschaffenheit der
Wände und Decken. Durch die Verwendung einer
gewinnbringenden Empfangsantenne lässt sich die
Reichweite erheblich vergrößern.
4
Inbetriebnahme
4.1 Platzierung von Sender und Empfänger
Erfahrungen aus der Praxis haben gezeigt, dass ein
optimaler Empfang bei einer Aufstellung in einer
Höhe von mindestens 1,5 m bis 2 m über dem Boden
erreicht wird. Um eine gute Montagestelle zu ermitteln, sollte ein Probebetrieb erfolgen. Die Übertragungsqualität kann sich durch Verschieben des Senders und/oder des Empfängers um nur einige Zentimeter erheblich ändern.
4.2 Montage
1) Um den Empfänger nach der Montage anschließen zu können, zuerst das Innenteil (2) aus
dem Gehäuse ziehen. Dazu die beiden Haltenasen (1) nach außen drücken, sodass sich das
Innenteil herausziehen lässt.
2) Das Innenteil über die Halterung (3) an einer
Wand oder an einem Mast so befestigen, dass die
Kabeldurchführungen (5) nach unten zeigen und
kein Niederschlag in das Gerät gelangen kann.
Bei einer Mastmontage die beiliegende Schelle
mit den Flügelmuttern und den Schrauben nach
Abb. 1 verwenden.
3) Die beiliegende Antenne in die SMA-Buchse (4)
stecken und festschrauben. Um eine größere
Reichweite zu erhalten, kann an diese Buchse
aber auch eine andere 2,4-GHz-Antenne der Serie
DX-… von MONACOR angeschlossen werden.
4) Nach dem Anschluss (Kap. 4.3) und den Einstellungen (Kap. 4.4) das Gehäuse aufsetzen.
4.3 Geräte anschließen
Vor dem Anschluss von Geräten diese zuvor ausschalten. Die Stromversorgung für den Empfänger
grundsätzlich zuletzt anschließen. Zum Ändern bestehender Anschlüsse zuerst die Stromversorgung
für den Empfänger und die angeschlossenen Geräte
ausschalten.
Alle Anschlüsse erfolgen über die Klemmleiste (9).
Es können Anschlussdrähte mit einem Querschnitt
4.3.1 Überwachungsmonitor / Fernsehgerät
1) Den Videoeingang des Monitors über ein 75-ΩKoaxialkabel mit der Klemme 8 „Video“ verbinden
und die Abschirmung mit der Klemme 7 „GND“.
2) Wird auch ein Ton übertragen, den Audioeingang
des Monitors über ein abgeschirmtes Audiokabel
an die Klemme 6 „Audio A“ anschließen und
bei einem Stereoton zusätzlich an die Klemme 4
„Audio B“. Die Abschirmung an die Klemme 5 bzw.
3 „GND“ anschließen.
3) Anstelle eines Monitors lässt sich auch ein Fernsehgerät anschließen. Falls am Fernsehgerät kein
Video- und Audioeingang vorhanden ist, kann der
Empfänger über einen HF-Modulator (z. B. VAM-3
von MONACOR) an die Antennenbuchse des
Fernsehgerätes angeschlossen werden.
4.3.2 Signalgeber oder anderes Zusatzgerät
Ist der verwendete Sender mit einem Schaltkanal
ausgestattet, lässt sich ein Vorgang an einem Gerät
auslösen, das an dem Empfänger angeschlossen ist.
Zum Beispiel kann ein optischer oder akustischer
Signalgeber aktiviert oder die Aufnahme eines Videorecorders gestartet werden. Der Anschluss ist in der
Abb. 3 dargestellt, wobei der Widerstand R1 das anzuschließende Gerät symbolisiert.
Wird zur Ansteuerung ein Strom von mehr als
80 mA benötigt, ein Relais oder einen Schaltverstärker zwischenschalten. Beim Anschluss einer induktiven Last (z. B. Relais) muss die Schutzdiode D1 in
Sperrrichtung parallel dazu angeschlossen werden!
4.3.3 Stromversorgung
Zur Stromversorgung wird ein stabilisiertes Netzgerät
mit einer Ausgangsspannung zwischen 7 V
und
30 V benötigt, z. B. PS-500ST von MONACOR. Die
Stromaufnahme beträgt 150 mA bei 12 V.
1) Bei Netzgeräten mit variabler Ausgangsspannung
diese zwischen 7 V und 30 V einstellen.
2) Das Netzgerät anschließen:
den Pluspol an die Klemme 2 „DC +7.. 30V“ und
den Minuspol an die Klemme 1 „GND“.
3) Erst wenn alle Anschlüsse hergestellt sind, das
Netzgerät an eine Steckdose (230 V~/50 Hz) anschließen. Mit dem Anlegen der Betriebsspannung
ist der Empfänger eingeschaltet. Die Betriebsanzeige (7) leuchtet.
4.4 Einstellungen vornehmen
4.4.1 Kanalwahl
Die Funkübertragung erfolgt im 2,4-GHz-Bereich auf
fünf Kanälen mit einem Abstand von 14 MHz. Maximal können gleichzeitig drei Kanäle benutzt werden
(Kanal 1, 3 und 5), weil zwei direkt nebeneinander liegende Kanäle sich stören.
Den Empfänger mit dem Drehschalter (8) auf den
Kanal des Senders einstellen:
Pos.
0, 1
2
3
4
5
6, 7, 8
9
A
B–F
Kanal
1 2,4145 GHz
2 2,4285 GHz
3 2,4425 GHz
4 2,4565 GHz
5 2,4705 GHz
1 2,4145 GHz
autom. Umschalten zwischen Kanal 1 und 5*
autom. Umschalten zwischen Kanal 1, 3 und 5*
1 2,4145 GHz
DEUTSCH
von 0,14 – 1 mm2 verwendet werden. Zum Hineinstecken oder Herausziehen eines Drahtes die zugehörige orange Lasche drücken. Eine der Kabeldurchführungen (5) durchbohren und das Anschlusskabel
durchstecken.
* Beim Umschaltbetrieb mit dem Regler „Auto - Time“
(6) die Verweildauer (ca. 1 – 20 s) einstellen.
4.4.2 Videosignal einstellen
Mit dem Schalter (11) die Polarität des Videosignals
entsprechend dem gesendeten Signal einstellen:
Position „normal“ bei normgerechter Übertragung,
Position „invers“ bei invertiert gesendetem Signal zur
Verschlüsselung.
Der Videoausgangspegel an der Klemme 8 „Video“
ist normgerecht auf 1 Vss eingestellt. Wenn jedoch
auf dem Bildschirm das Bild zu hell oder zu dunkel
erscheint, mit dem Regler „Videopegel“ (10) den
Pegel entsprechend anpassen.
5
Technische Daten
Empfangsfrequenzen: . . . Kanal 1 2,4145 GHz
Kanal 2 2,4285 GHz
Kanal 3 2,4425 GHz
Kanal 4 2,4565 GHz
Kanal 5 2,4705 GHz
Antenne: . . . . . . . . . . . . . Rundstrahlantenne
Reichweite: . . . . . . . . . . . siehe Kapitel 3
Video
Ausgangspegel: . . . . . . 0,7 – 1,2 Vss an 75 Ω
Bandbreite: . . . . . . . . . 30 Hz – 5 MHz
Audio (2 Tonkanäle)
Ausgangspegel: . . . . . . 500 mV an 1 kΩ
Bandbreite: . . . . . . . . . 15 Hz – 15 kHz
Ausgang Schaltkanal: . . . offener Kollektor,
max. 15 V/80 mA
Stromversorgung: . . . . . . 7 – 30 V /
150 mA bei 12 V
Gehäuseschutzklasse: . . IP 54
Einsatztemperatur: . . . . . –10 °C bis +55 °C
Abmessungen
ohne Antenne: . . . . . . . . . 180 x 135 x 70 mm
Gewicht: . . . . . . . . . . . . . . 370 g
Änderungen vorbehalten.
Diese Bedienungsanleitung ist urheberrechtlich für MONACOR ® INTERNATIONAL GmbH & Co. KG
geschützt. Eine Reproduktion für eigene kommerzielle Zwecke – auch auszugsweise – ist untersagt.
7
ENGLISH
Please unfold page 5. Then you can always see the
operating elements and connections described.
1
1
2
3
4
5
6
7
8
9
10
11
2
Operating Elements and Connections
Latch for holding the housing
Inside part (also see fig. 2)
Wall and pole support
SMA antenna jack
Cable inlet
Control for the dwell time (approx. 1 – 20 s) of a
camera picture in the switching mode
Internal power LED
Rotary switch for adjusting the receiving channel
Position Channel
0, 1
1
2
2
3
3
4
4
5
5
6, 7, 8
1
9
automatic switching between 1 + 5
A
automatic switching between 1 + 3 + 5
B–F
1
10-pole terminal strip for all connections, for wire
cross sections from 0.14 to 1 mm2.
(To plug in or pull out a wire, press the corresponding orange strip.)
Control to correct the video level;
the video level is adjusted according to standard
(1 Vpp) but it can be changed to 0.7 – 1.2 Vpp
Selector switch for the video signal polarity
normal polarity according to standard
invers the video signal is inverted;
(for encoded transmission if the transmitter is also able to send the video signal in
an inverted way)
Important Notes
The receiver corresponds to all required directives of
the EU and is therefore marked with .
● Do not operate the receiver in areas of very high or
very low temperatures (admissible ambient temperature range -10 °C to +55 °C).
● For cleaning of the housing do not use any strong
detergents or chemicals.
● No guarantee claims for the receiver and no liability
for any resulting personal damage or material
damage will be accepted if the receiver is used for
other purposes than originally intended, if it is not
correctly mounted or operated, or not repaired in an
expert way.
8
If the receiver is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
3
Applications
In connection with a 2.4 GHz transmitter or a 2.4 GHz
wireless surveillance camera of the series “AV-...”
from MONACOR, the receiver AV-3030RDX serves
for wireless audio and video transmission. With additional units of the MONACOR range it is possible to
set up a wireless video surveillance system. Due to
the weatherproof housing (IP54) the AV-3030RDX is
especially suitable for outdoor mounting.
The transmission range largely depends on the
local conditions, the transmitter used, and the reception antenna used. In the open, the range can extend
up to 500 m, in buildings up to 50 m depending on the
condition of the walls and ceilings. By using a reception antenna with gain, the range can considerably be
increased.
4
Setting into Operation
4.1 Placing of transmitter and receiver
Practical experience has shown that an optimum
reception is reached when placing the units at a minimum height of 1.5 m to 2 m above the ground. To find
a good place of mounting, a trial run is recommended.
The transmission quality can substantially be changed
by displacing the transmitter and/or the receiver by a
few centimetres only.
4.2 Mounting
1) To be able to connect the receiver after mounting,
first pull out the inside part (2) of the housing. For
this purpose press the two latches (1) outwards so
that the inside part can be pulled out.
2) Fix the inside part via the support (3) to a wall or a
pole so that the cable inlets (5) point downwards
and no rain can penetrate the unit.
In case of pole mounting use the supplied clip
with the wing nuts and the screws according to fig. 1.
3) Connect the supplied antenna to the SMA jack (4)
and screw it down. To obtain a larger range, another 2.4 GHz antenna of the series DX-... from
MONACOR may also be connected to this jack.
4) After the connection (chapter 4.3) and adjustments (chapter 4.4) place the housing.
4.3 Connection of the units
Prior to the connection of units, switch them off.
Always connect the power supply for the receiver last
of all. To change existing connections, first disconnect
the power supply for the receiver and switch off the
connected units.
4.3.1 Surveillance monitor/TV set
1) Connect the video input of the monitor via a 75 Ω
coaxial cable to terminal 8 “Video” and the screening to terminal 7 “GND”.
2) If sound is transmitted as well, connect the audio
input of the monitor via a screened audio cable to
terminal 6 “Audio A”, in case of stereo sound additionally to terminal 4 “Audio B”. Connect the
screening to terminal 5 or 3 “GND”.
3) Instead of a monitor it is also possible to connect a
TV set. If the TV set is not provided with a video
and audio input, the receiver can be connected via
an RF modulator (e. g. VAM-3 from MONACOR) to
the antenna jack of the TV set.
4.3.2 Signal device or other additional unit
If the transmitter used is equipped with a control
channel, it is possible to trigger an action at a unit
which is connected to the receiver. For example, it is
possible to activate a visual or acoustical signal
device or to start the recording of a video recorder.
The connection is shown in fig. 3, the unit to be
connected is symbolized by the resistor R1.
If a current of more than 80 mA is required for the control, insert a relay or a switching amplifier. When
connecting an inductive load (e. g. relay), the protective diode D1 must be connected in parallel to it in
reverse direction!
4.3.3 Power supply
As a power supply a regulated power supply unit with
an output voltage between 7 V and 30 V is required, e. g. PS-500ST from MONACOR. The current
consumption is 150 mA at 12 V.
1) In case of power supply units with variable output
voltage adjust them between 7 V and 30 V.
2) Connect the power supply unit:
the positive pole to terminal 2 “DC +7.. 30V” and
the negative pole to terminal 1 “GND”.
3) Do not connect the power supply unit to a mains
socket (230 V~/50 Hz) until all connections have
been made. When applying the operating voltage,
the receiver is switched on. The power LED (7)
lights up.
4.4 Making the adjustments
4.4.1 Channel selection
The wireless transmission is made in the 2.4 GHz
range on five channels at a distance of 14 MHz. As a
maximum three channels can be used at the same
time (channels 1, 3, and 5) because two adjacent
channels interfere with each other.
Adjust the receiver with the rotary switch (8) to the
channel of the transmitter:
Pos.
0, 1
2
3
4
5
6, 7, 8
9
A
B–F
Canale
1 2,4145 GHz
2 2,4285 GHz
3 2,4425 GHz
4 2,4565 GHz
5 2,4705 GHz
1 2,4145 GHz
cambio automatico fra i canali 1 e 5*
cambio automatico fra i canali 1, 3 e 5*
1 2,4145 GHz
ENGLISH
All connections are made via the terminal strip (9).
Connection wires with a cross section from 0.14 to
1 mm2 may be used. To plug in or pull out a wire, press
the corresponding orange strip. Pierce one of the cable
inlets (5) and pass the connection wire through it.
* In the switching mode adjust the dwell time (approx.
1 – 20 s) with the control “Auto-Time” (6).
4.4.2 Adjusting the video signal
Adjust the polarity of the video signal with the switch
(11) according to the signal transmitted:
Position “normal” for transmission according to standard, position “invers” when a signal is sent in an
inverted way for encoding.
The video output level at terminal 8 “Video” is
adjusted to 1 Vpp according to standard. However, if
the picture on the screen appears too bright or too
dark, match the level with the control “Videopegel”
(10) accordingly.
5
Specifications
Receiving frequencies: . . channel 1 2.4145 GHz
channel 2 2.4285 GHz
channel 3 2.4425 GHz
channel 4 2.4565 GHz
channel 5 2.4705 GHz
Antenna: . . . . . . . . . . . . . omnidirectional antenna
Range: . . . . . . . . . . . . . . . see chapter 3
Video
output level: . . . . . . . . . 0.7 – 1.2 Vpp at 75 Ω
bandwidth: . . . . . . . . . . 30 Hz – 5 MHz
Audio (2 audio channels)
output level: . . . . . . . . . 500 mV at 1 kΩ
bandwidth: . . . . . . . . . . 15 Hz – 15 kHz
Output control channel: . . open collector,
max. 15 V/80 mA
Power supply: . . . . . . . . . 7 – 30 V /
150 mA at 12 V
Protective class
of housing: . . . . . . . . . . . . IP 54
Ambient temperature: . . . -10 °C to +55 °C
Dimensions w/o antenna: 180 x 135 x 70 mm
Weight: . . . . . . . . . . . . . . . 370 g
Subject to technical modification.
All rights reserved by MONACOR ® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
be reproduced in any form or by any means for any commercial use.
9
FRANÇAIS
Ouvrez le présent livret page 5 de manière à
visualiser les éléments et branchements décrits.
1
1
2
3
4
5
6
7
8
9
10
11
2
Eléments et branchements
Languette pour maintenir le boîtier
Partie intérieure (voir également schéma 2)
Support mural et pour mât
Prise antenne femelle SMA
Guide-câble
Réglage pour la durée d’affichage (1 – 20 secondes environ) d’une image de caméra en mode
commutation
Témoin interne d’affichage
Sélecteur rotatif pour régler le canal de réception
Pos.
Canal
0, 1
1
2
2
3
3
4
4
5
5
6, 7, 8 1
9
commutation automatique entre 1 + 5
A
commutation automatique entre 1 + 3 + 5
B–F
1
Barrette 10 pôles pour tous les branchements,
pour sections de conducteurs de 0,14 – 1 mm2
(Pour insérer ou retirer un conducteur appuyez
sur la patte orange correspondante).
Réglage pour corriger le niveau vidéo ;
selon la norme, le niveau vidéo est réglé à 1 Vcc,
si besoin, il peut être modifié sur 0,7 – 1,2 Vcc.
Sélecteur pour la polarité du signal vidéo :
normal : polarité selon la norme
invers : le signal vidéo est inversé ;
(pour une transmission codée, si l’émetteur peut également émettre le signal
vidéo inversé)
Conseils importants d’utilisation
Le récepteur répond à toutes les directives nécessaires
de l’Union Européenne et porte donc le symbole .
● Ne faites pas fonctionner le récepteur dans des
zones soumises à des températures très élevées
ou très basses (plage de température de fonctionnement autorisée : -10 °C à +55 °C).
● Pour le nettoyer, n‘utilisez en aucun cas de détergents aggressifs ou de produits chimiques.
● Nous déclinons toute responsabilité en cas de
dommages corporels ou matériels résultants si le
récepteur est utilisé dans un but autre que celui
pour lequel il a été conçu, s’il n’est pas correctement installé, utilisé ou réparé par une personne
habilitée; en outre, la garantie deviendrait caduque.
Lorsque le récepteur est définitivement retiré
du service, vous devez le déposer dans une
usine de recyclage de proximité pour contribuer à son élimination non polluante.
10
3
Possibilités d’utilisation
Le récepteur AV-3030RDX, combiné à un émetteur
2,4 GHz ou à une caméra de surveillance sans fil
2,4 GHz de la série “AV-…” de MONACOR, sert pour
une transmission sans fil de signaux vidéo et audio.
On peut créer une installation de surveillance vidéo
sans fil avec des appareils supplémentaires de la
gamme MONACOR. Grâce au boîtier étanche IP 54,
le AV-3030RDX est spécialement adapté pour un
montage en extérieur.
La portée de transmission dépend grandement de
la configuration des lieux d’utilisation, l’émetteur utilisé et l’antenne de réception utilisée. Lorsqu’il n’y a
pas d’obstacle entre le récepteur et l’antenne de
réception utilisée, elle peut atteindre 500 m. Dans des
bâtiments, elle diminue jusqu’à 50 m selon la composition des murs et plafonds. Si vous utilisez une
antenne avec gain sur le récepteur, la portée peut
être augmentée plusieurs fois.
4
Fonctionnement
4.1 Placement de l’émetteur et du récepteur
L’expérience montre que la réception est optimale
pour un positionnement des appareils à une hauteur
de 1,5 m à 2 m au moins au-dessus du sol. Pour trouver une bonne place de montage, il est conseillé d’effectuer un test car un déplacement de l’émetteur
et/ou du récepteur de quelques centimètres uniquement peut modifier considérablement la qualité de
transmission.
4.2 Montage
1) Pour pouvoir relier le récepteur après le montage,
retirez tout d’abord la partie intérieure (2) du
boîtier. Pour ce faire, poussez vers l’extérieur les
deux languettes (1) de manière à pouvoir sortir la
partie intérieure.
2) Fixez la partie intérieure via le support (3) à un mur
ou un mât de telle sorte que les guide-câbles (5)
soient orientés vers le bas et qu’aucune précipitation ne puisse entrer dans l’appareil.
Pour un montage sur un mât, utilisez le collier
de serrage livré avec les écrous papillon et les vis
selon les indications du schéma 1.
3) Placez l’antenne livrée dans la prise SMA (4) et
vissez. Pour obtenir une plus grande portée, on
peut brancher également à cette prise une autre
antenne 2,4 GHz de la série DX-… de MONACOR.
4) Après le branchement (chapitre 4.3), et les réglages (schéma 4.4), replacez le boîtier.
4.3 Branchement des appareils
Avant de brancher les appareils, veillez à les éteindre. Reliez l’alimentation pour le récepteur toujours
en dernier. Pour modifier les branchements existants,
coupez tout d’abord l’alimentation pour le récepteur
et les appareils reliés.
Tous les branchements s’effectuent via la barrette
(9) ; il est possible d’utiliser des conducteurs avec
4.3.1 Moniteur de surveillance /Téléviseur
1) Reliez l’entrée vidéo du moniteur à la borne 8
“Video” via un câble coaxial 75 Ω et le blindage à la
borne 7 “GND”.
2) Si un son est également transmis, reliez l’entrée
audio du moniteur via un cordon audio blindé à la
borne 6 “Audio A” et pour un son stéréo, en plus à
la borne 4 “Audio B”. Reliez le blindage à la borne
5 ou 3 “GND”.
3) A la place d’un moniteur, on peut relier un téléviseur. Si sur le téléviseur, aucune entrée vidéo et
audio n’est prévue, le récepteur peut être relié à la
prise antenne du téléviseur via un modulateur HF
(par exemple VAM-3 de MONACOR).
4.3.2 Avertisseurs de signaux ou autre appareil
supplémentaire
Si l’émetteur utilisé est équipé d’un canal de commutation, un processus peut se déclencher à un appareil
relié au récepteur. Par exemple, un avertisseur acoustique ou optique peut être activé ou l’enregistrement
d’un magnétoscope peut être démarré. Le branchement est présenté sur le schéma 3 où la résistance
R1 symbolise l’appareil à relier.
Si pour le fonctionnement, un courant de plus de
80 mA est nécessaire, intercalez un relais ou un
amplificateur de commutation. Lors du branchement
d’une charge inductive (par exemple relais), la diode
de protection D1 doit être branchée en parallèle dans
le sens de blocage.
4.3.3 Alimentation
Pour l’alimentation, une alimentation stabilisée avec
une tension de sortie entre 7 V et 30 V est nécessaire, par exemple PS-500ST de MONACOR. La
consommation est de 150 mA sous 12 V.
1) Pour des alimentations à tension de sortie variable,
réglez-la entre 7 V et 30 V.
2) Reliez l’alimentation : le pôle plus à la borne 2 “DC
+7.. 30V” et le pôle moins à la borne 1 “GND”.
3) Une fois tous les branchements effectués, reliez
l’alimentation à une prise secteur 230 V~/50 Hz.
Le récepteur est allumé lorsque la tension de fonctionnement est appliquée. Le témoin de fonctionnement (7) brille.
4.4 Réglages
4.4.1 Sélection du canal
La transmission sans fil s’effectue dans la plage
2,4 GHz, divisée en cinq canaux avec une distance
de 14 MHz. On peut utiliser simultanément trois
canaux (canal 1, 3 et 5) au plus car deux canaux
directement consécutifs se perturbent.
Réglez le récepteur avec le réglage (8) sur le
canal de l’émetteur :
Pos.
0, 1
2
3
4
5
6, 7, 8
9
A
B–F
Canal
1 2,4145 GHz
2 2,4285 GHz
3 2,4425 GHz
4 2,4565 GHz
5 2,4705 GHz
1 2,4145 GHz
commutation automatique entre canal 1 + 5*
commutation automatique entre canal 1 + 3 + 5*
1 2,4145 GHz
FRANÇAIS
une section de 0,14 – 1 mm2. Pour insérer ou retirer
un conducteur, appuyez sur la patte orange correspondante. Percez un des guide-câbles (5) et faites
passer le câble.
* En mode de commutation, réglez la durée d’affichage
(1 – 20 s environ) avec le réglage “Auto-Time” (6).
4.4.2 Réglage du signal vidéo
Avec le sélecteur (11), réglez la polarité du signal
vidéo selon le signal émis : position “normal” pour une
transmission selon la norme, position “invers” pour un
signal émis inversé pour codage.
Le niveau de sortie vidéo à la borne 8 “Video” est,
selon la norme, réglé à 1 Vcc. Si cependant l’image
sur l’écran est trop claire ou trop sombre, adaptez le
niveau avec le réglage “Videopegel” (10) en conséquence.
5
Caractéristiques techniques
Fréquences de réception : canal 1 2,4145 GHz
canal 2 2,4285 GHz
canal 3 2,4425 GHz
canal 4 2,4565 GHz
canal 5 2,4705 GHz
Antenne : . . . . . . . . . . . . . omnidirectionnelle
Portée : . . . . . . . . . . . . . . voir chapitre 3
Vidéo
Niveau de sortie : . . . . . 0,7 – 1,2 Vcc sous 75 Ω
Largeur de bande : . . . 30 Hz – 5 MHz
Audio (2 sons)
Niveau de sortie : . . . . . 500 mV sous 1 kΩ
Largeur de bande : . . . 15 Hz – 15 kHz
Sortie canal de
commutation : . . . . . . . . . collecteur ouvert,
max. 15 V/80 mA
Alimentation : . . . . . . . . . . 7 – 30 V /
150 mA sous 12 V
Classe de protection
du boîtier : . . . . . . . . . . . . IP 54
Température fonc. : . . . . . –10 °C jusqu’à +55 °C
Dimensions sans antenne : 180 x 135 x 70 mm
Poids : . . . . . . . . . . . . . . . 370 g
Tout droit de modification réservé.
Notice d’utilisation protégée par le copyright de MONACOR ® INTERNATIONAL GmbH & Co. KG. Toute reproduction même partielle à des fins commerciales est interdite.
11
ITALIANO
Vi preghiamo di aprire completamente la pagina 5.
Così vedrete sempre gli elementi di comando e i
collegamenti descritti.
1
1
2
3
4
5
6
7
8
9
10
11
2
Elementi di comando e collegamenti
Linguetta per trattenere il contenitore
Interno (vedi anche fig. 2)
Supporto a parete o asta
Presa SMA per antenna
Passacavi
Regolatore per la durata (ca. 1 – 20 s) di un’immagine nella modalità sequenziale
Spia interna di funzionamento
Selettore per impostare il canale di ricezione
Pos.
Canale
0, 1
1
2
2
3
3
4
4
5
5
6, 7, 8 1
9
cambio automatico fra 1 + 5
A
cambio automatico fra 1 + 3 + 5
B–F
1
Morsettiera a 10 poli per tutti i collegamenti, per
conduttori con sezione 0,14 – 1 mm2
(Per inserire o staccare un conduttore, premere la
relativa linguetta arancione.)
Regolatore per correggere il livello video;
il livello video è impostato secondo norma (1 Vpp),
ma può essere variato fra 0,7 – 1,2 Vpp
Commutatore per la polarità del segnale video
normal polarità secondo norma
invers segnale video invertito;
(per una trasmissione codificata se
anche il trasmettitore è in grado di inviare
il segnale video in modo invertito)
Avvertenze importanti per l’uso
Il ricevitore è conforme a tutte le direttive richieste
dell’UE e pertanto porta la sigla .
● Non usare il ricevitore in zone con temperature
molto alte o molto basse (temperatura d’impiego
ammessa fra -10 °C e +55 °C).
● Per la pulizia del contenitore non usare detersivi
aggressivi o prodotti chimici.
● Nel caso d’uso improprio, d’installazione sbagliata,
d’impiego scorretto o di riparazione non a regola
d’arte del ricevitore, non si assume nessuna responsabilità per eventuali danni consequenziali a
persone o a cose e non si assume nessuna garanzia per il ricevitore .
Se si desidera eliminare il ricevitore definitivamente, consegnarlo per lo smaltimento ad
un’istituzione locale per il riciclaggio.
12
3
Possibilità d’impiego
Il ricevitore AV-3030RDX insieme ad un trasmettitore
a 2,4 GHz o a una telecamera wireless di sorveglianza della serie “AV-...” di MONACOR, serve per la
trasmissione wireless di segnali video e audio. Con
apparecchi supplementari dal programma MONACOR
è possibile creare un impianto di sorveglianza video
senza fili. Grazie al contenitore resistente alle intemperie (IP 54), l’AV-3030RDX è particolarmente adatto
per il montaggio all’esterno.
La portata di trasmissione dipende fortemente
dalle condizioni locali, dal trasmettitore e dall’antenna
di ricezione impiegata. Se non ci sono ostacoli fra
trasmettitore e ricevitore, può arrivare fino a 500 m.
Negli edifici, la portata è ridotta per via delle pareti e
dei soffitti, a seconda delle loro caratteristiche, a 50 m
ca. Impiegando un’antenna con guadagno sul ricevitore, la portata può essere aumentata più volte.
4
Messa in funzione
4.1 Posizionamento del trasmettitore e del
ricevitore
L’esperienza pratica ha dimostrato che si ottiene una
ricezione ottimale posizionando gli apparecchi ad
un’altezza di non meno di 1,5 m a 2 m dal pavimento.
Per trovare un buon posto per il montaggio conviene
fare delle prove, perché uno spostamento del trasmettitore e/o del ricevitore di pochi centimetri può
modificare notevolmente la qualità di trasmissione.
4.2 Montaggio
1) Per poter collegare il ricevitore dopo il montaggio
occorre dapprima sfilare l’interno (2) dal contenitore. Per fare ciò, premere verso l’esterno le due
linguette (1) in modo da poter sfilare la parte
interna.
2) Fissare la parte interna ad una parete o ad un’asta
servendosi del supporto (3) e in modo che i passacavi (5) siano orientati verso il basso e non
possa entrare pioggia o umidità nell’apparecchio.
Nel caso di montaggio ad un’asta, usare la fascetta in dotazione con i dadi ad alette e le viti
come illustrato in fig. 1.
3) Inserire l’antenna in dotazione nella presa SMA (4)
ed avvitare bene. Per aumentare la portata, alla
presa si può collegare anche un’altra antenna da
2,4 GHz della serie DX-… di MONACOR.
4) Dopo il collegamento (cap. 4.3) e dopo le impostazioni (cap. 4.4) rimettere il contenitore.
4.3 Collegare gli apparecchi
Prima di collegare degli apparecchi occorre spegnerli. Per principio, collegare come ultima l’alimentazione per il ricevitore. Per modificare dei collegamenti
esistenti, staccare prima l’alimentazione per il ricevitore e spegnere gli apparecchi collegati.
Tutti i collegamenti si fanno con la morsettiera (9).
Si possono usare conduttori con una sezione di
0,14 – 1 mm2. Per inserire o sfilare un conduttore, pre-
4.3.1 Monitor di sorveglianza / televisore
1) Collegare l’ingresso video del monitor per mezzo
di un cavo coassiale 75 Ω con il morsetto 8 “Video”
e la schermatura con il morsetto 7 “GND”.
2) Per la trasmissione audio, collegare l’ingresso
audio del monitor con il morsetto 6 “Audio A” servendosi di un cavo audio schermato e, nel caso di
una trasmissione stereo, in più on il morsetto 4
“Audio B”. Collegare la schermatura rispettivamente con il morsetto 5 o 3 “GND”.
3) Al posto di un monitor si può collegare anche un
televisore. Se il televisore non dispone di un
ingresso video e audio, il ricevitore può essere collegato con la presa per antenna del televisore
usando un modulatore HF (p. es. VAM-3 di
MONACOR).
4.3.2 Segnalatori o altri apparecchi supplementari
Se il trasmettitore usato dispone di un canale di controllo, è possibile attivare con questo un evento su un
apparecchio collegato al ricevitore. Per esempio si
può attivare un segnalatore acustico o ottico oppure
si può avviare la registrazione di un videoregistratore.
Il collegamento è illustrato in fig. 3, dove la resistenza
R1 rappresenta l’apparecchio da collegare.
Se per il comando è richiesta una corrente di oltre
80 mA, occorre inserire un relè o un amplificatore dei
segnali di controllo. Collegando un carico induttivo
(p. es. relè) il diodo di protezione D1 deve essere collegato in direzione del blocco e in parallelo!
4.3.3 Alimentazione
Per l’alimentazione è richiesto un alimentatore stabilizzato con tensione d’uscita fra 7 V e 30 V , p. es.
PS-500ST di MONACOR. L’assorbimento di corrente,
con 12 V, è di 150 mA max.
1) In caso di alimentatori con tensione d’uscita variabile impostare la tensione fra 7 V e 30 V.
2) Collegare l’alimentatore:
il polo positivo con il morsetto 2 “DC +7 .. 30V” e il
negativo con il morsetto 1 “GND”.
3) Solo dopo aver effettuato tutti i collegamenti, collegare l’alimentatore con una presa di rete (230 V~/
50 Hz). Dopo aver applicato al tensione d’esercizio, il ricevitore è acceso. La spia interna di funzionamento (7) rimane accesa.
4.4 Effettuare le impostazioni
4.4.1 Scelta dei canali
La trasmissione wireless avviene nel settore dei
2,4 GHz, suddiviso in cinque canali distanti 14 MHz gli
uni dagli altri. Si possono usare contemporaneamente al massimo tre canali (canali 1, 3 e 5), perché
due canali adiacenti creerebbero delle interferenze.
Con il selettore (8) impostare sul ricevitore il
canale del trasmettitore:
Pos.
0, 1
2
3
4
5
6, 7, 8
9
A
B–F
Canale
1 2,4145 GHz
2 2,4285 GHz
3 2,4425 GHz
4 2,4565 GHz
5 2,4705 GHz
1 2,4145 GHz
cambio automatico fra i canali 1 e 5*
cambio automatico fra i canali 1, 3 e 5*
1 2,4145 GHz
ITALIANO
mere la relativa linguetta arancione. Forare uno dei
passacavi (5) e fare passare il cavo di collegamento.
* Nel funzionamento sequenziale impostare la durata
della singola immagine (ca. 1 – 20 s) per mezzo del
regolatore “Auto - Time” (6).
4.4.2 Impostare il segnale video
Con il commutatore (11) impostare la polarità del segnale video secondo il segnale trasmesso:
posizione “normal” in caso di trasmissione a norma,
posizione “invers” in caso di segnale inviata, per codifica, in modo invertito.
Il livello d’uscita del segnale video al morsetto 8
“Video” è impostato su 1 Vpp come da norma. Tuttavia, se l’immagine risulta troppo chiara o troppo scura
sullo schermo, è possibile adattare il livello con il
regolatore “Videopegel” (10).
5
Dati tecnici
Frequenze di ricezione: . . Canale 1 2,4145 GHz
Canale 2 2,4285 GHz
Canale 3 2,4425 GHz
Canale 4 2,4565 GHz
Canale 5 2,4705 GHz
Antenna: . . . . . . . . . . . . . onnidirezionale
Portata: . . . . . . . . . . . . . . vedi capitolo 3
Video
Livello d’uscita : . . . . . . 0,7 – 1,2 Vpp con 75 Ω
Banda passante: . . . . . 30 Hz – 5 MHz
Audio (2 canali audio)
Livello d’uscita: . . . . . . 500 mV con 1 kΩ
Banda passante: . . . . . 15 Hz – 15 kHz
Uscita canale di controllo: collettore aperto,
max. 15 V/80 mA
Alimentazione: . . . . . . . . . 7 – 30 V /
150 mA con 12 V
Grado di protezione
del contenitore: . . . . . . . . IP 54
Temperatura d’esercizio: . -10 °C a +55 °C
Dimensioni
senza antenna: . . . . . . . . 180 x 135 x 70 mm
Peso: . . . . . . . . . . . . . . . . 370 g
Con riserva di modifiche tecniche.
La MONACOR ® INTERNATIONAL GmbH & Co. KG si riserva ogni diritto di elaborazione in qualsiasi forma
delle presenti istruzioni per l’uso. La riproduzione – anche parziale – per propri scopi commerciali è vietata.
13
®
Copyright © by MONACOR INTERNATIONAL GmbH & Co. KG, Bremen, Germany. All rights reserved. A-0684.98.01.12.2006